• On sale!
Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB or RGBW
  • Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB or RGBW
  • Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB or RGBW
  • Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB or RGBW
  • Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB or RGBW
Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB or RGBW
Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB or RGBW Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB or RGBW Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB or RGBW Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB or RGBW

Dalcnet DMX Interface 12-24V 4 x 5A LED Dimmer RGB / RGBW control

DLX1224-4CV-DMX

$52.12
24 / 48 hours

BUS + SEQUENCER + FADER + DIMMER + DRIVER ,DMX control interface operated 12-24V with 4 channels of 5A (max 10A total). dimensions: 88 x 54 x 26 mm

Read more ...
local_shipping Shipped in 1-2 days
check
In stock
3 Items

Quantity

payments You can pay in installments with PAYPAL OR SCALAPAY
Description
Product Information:

Four-channel LED dimmer that allows you to adjust the intensity of the LED light by DMX + RDM bus command. The power supply voltage is 12 to 24V DC. The output signal varies in the range of the supply voltage and allows to control a voltage load, up to a maximum value of 2.5A per output channel (max 10A tot.). The intensity curve has been designed to ensure excellent quality in visual comfort and can be adjusted via the BUS signal, DMX512 + RDM.

  • DC Input 12-24 Vdc
  • Bus command: DMX512+RDM or DALI
  • Local command: Stand alone function (Dip Switch settings)
  • Control: RGB or RGBW Colour
  • Current outputs or voltage outputs for LED strip
  • Typical efficiency > 95%
  • Adjusting the brightness up to completed off
  • Soft start and soft stop
  • Optimized output curve
  • Extended temperature range
  • 100% Test functional , 5 Years warranty

Installation:

  • Installation and maintenance must be performed only by qualified personnel in compliance with current regulations.
  • The product must be installed inside an electrical panel protected against overvoltages.
  • The product must be installed in a vertical or horizontal position with the cover / label upwards or vertically; Other positions are not permitted. It is not permitted to bottom-up position (with the cover/label down).
  • Keep separated the circuits at 230V (LV) and the circuits not SELV from circuits to low voltage (SELV) and from any connection with this product. It is absolutely forbidden to connect, for any reason whatsoever, directly or indirectly, the 230V mains voltage to the bus or to other parts of the circuit.

Power supply:

  • For the power supply use only a SELV power supplies with limited current, short circuit protection and the power must be dimensioned correctly. In case of using power supply with ground terminals, all points of the protective earth (PE = Protection Earth) must be connected to a valid and certified protection earth.
  • The connection cables between the power source 'low voltage' and the product must be dimensioned correctly and they should be isolated from every wiring or parts at voltage not SELV. Use double insulated cables.
  • Dimension the power supply for the load connected to the device. If the power supply is oversized compared with the maximum absorbed current, insert a protection against over-current between the power supply and the device.
  • For the constant current output, the voltage of LED module (Vf) must be less of 5V at the voltage of power supply.

Command:

  • The length of the connection cables at the BUS (DMX512, Modbus, DALI or other) use cables as per specification of the respective protocols and regulations and they should be isolated from every wiring or parts at voltage not SELV. Use double insulated shielded and twisted cables.
  • All the product and the control signal connect at the BUS (DMX512, Modbus, DALI or other) must be SELV (the devices connected must be SELV or supply a SELV signal)

Outputs:

  • The length of the connection cables between the product and the LED module must be less than 10m; the cables must be dimensioned correctly and they should be isolated from every wiring or parts at voltage not SELV. Is preferable to use shielded and twisted cables.

100% original product by

Details:
check
In stock
3 Items

Data sheet

Barcode:
8052575974899
Reference
DLX1224-4CV-DMX
Input voltage
12-24 V DC
Depth in mm
19
Width in mm
45
Length in mm
58
Degree of protection
IP20
Material
Pvc
Light source
LED
Current carrying capacity
10A
Insulation class
Insulation class II
Product accessories
Why buy to us
Trustpilot verified reviews
group_work Cookie consent